Arc for the spider improved 2x2 (Polymeric covering)

 

Choosing arcs for a spider is a task that arises for fishermen who want to build or repair fishing gear with their own hands. The modern range of components is quite wide. In addition to the parameters, the products differ in the material used for their manufacture. Seti Snasti online store offers a good offer for buyers who are looking for reliable and relatively inexpensive components: an improved onion for a fishing spider with corrosion protection.

 

What is a polymer?

The material for the manufacture of arcs presented to customers is a steel bar. Its diameter is 5 mm. A feature of the components is the presence of a polymer coating, that is, a protective layer specially applied to the surface of the products to increase their operational characteristics.

This is a thermal process made according to the military technology of the Kharkov plant. During the procedure, the metal is coated with an ultra-thin film, which prevents the penetration of moisture and oxidation. Due to the high quality of welding and processing (controlled by a master with 30 years of experience!), The spider arcs presented in the catalog fell into the category of the best available fishing components in the domestic market.

 

What is the difference between polymer-coated arcs and standard arcs?

The presence of a protective layer does not lead to a decrease in the elasticity of steel. Polymer-coated fishing arches can be used for fishing in all conditions, including adverse climatic zones, since the components have the following advantages:

• increased level of strength;

• excellent resistance to external factors: ultraviolet radiation, critically high and low temperatures, salt water, etc .;

• higher resistance to corrosion processes;

• the affordable price due to the low cost of technology.

Such a corrosion-resistant coating, such as polymer, allows you to increase the duration of operation of the arcs in comparison with the standard almost three times. And this means that there will be no need for their frequent replacement, so the use of such products is much more economical.

 

What arcs are represented in the assortment of the store?

Components are sold in a set with crosspieces. The finished kit includes one cross and four arcs. The company "Sete Snasti" provides regular and potential customers the opportunity to buy arcs on a spider with the following parameters:

• Spider 1x1m (arc length - 140 cm);

• Spider 1.5x1.5 (arc length - 180 cm);

• Spider 2x2 (arc length - 220 cm).

• Spider 2.5x2.5 (arc length 2.2m) (1.15cm when folded)

Note! All dimensions of the arcs are indicated in working condition: the numbers 1x1, 1.5x1.5, 2x2 do not describe the length of each arc, but the parameters of the finished spiders after installing components. And this means that the net fabric for gear must be selected in sizes 1x1, 1.5x1.5, 2x2, respectively.

 

How are arcs mounted on a spider?

At one end (lower), each arc enters the corner hole of the stop-hoist. Thus, the net web is fastened to the base. There is a small notch from this edge on the arc. It provides firm fixation of the net sheet and prevents it from slipping.

The second end (upper) all arcs enter the hole of the cross, connecting at a common peak. The advantage of acquiring arcs in a set with a crosspiece is 100% correspondence of the diameter of the elements to the size of the hole: the arcs will enter it freely (no physical the effort is required for installation), but they will not hang out and fall out.

 

How is spider fishing done?

This tackle serves as a tool for fishing and frying, as well as for fish of various varieties. The smaller the planned production size, the finer the grid in the net. Equipment is recommended in areas of water bodies where fish are concentrated in large quantities: spawning grounds, obstacles, hydraulic structures, slow circular backwaters adjacent to fences. The lower spider should be on a flat or slightly sloping bottom. 

Tackle lifting is carried out regularly after certain time intervals (e.g. 10 minutes). There are several ways to pull tackle out of the water. If fishing was carried out using small and medium-sized structures from a bridge or pier, they were manually pulled out with a rope. When fishing from a boat or shore, the required length is used to lift the equipment. Fishing spider is able to provide guaranteed fishing in large quantities.

  

Arc acquisition conditions

In our online store you can buy arcs on a spider (with a polymer coating) by placing an order directly on the website or by telephone, contacting the managers of the company. The advantages that our customers receive are:

 

  • free consultation of store employees regarding product selection;
  • customer loyalty programs (cumulative points system that allows you to get a discount on the product);
  • organization of delivery by transport companies to all regions of Ukraine;
  • lack of margins, and, therefore, the need to overpay for the brand and logistics.

We provide the opportunity to purchase sets of arcs not only at retail but also in bulk. To clarify the wholesale prices for components, please contact the managers at the telephone number listed on the site.

 

Evaluate the advantages of domestic components for fishing tools on your own experience without risk and overpayments.

Characteristics
Characteristics Материал - Леска 0.36мм; Размер паука - 2х2 метра

Write a review

Note: HTML is not translated!

Spider fishing from a fishing line 2 to 2m (Fatka, painter)

  • Brand: Украина
  • Product Code: Паук рыболовный из лески 2 на 2м (Фатка, малявочник)
  • Availability: In Stock
  • 437.00 грн.


Available Options


Viewed

Spider fishing from a fishing line 2 to 2m (Fatka, painter)

Spider fishing from a fishing line 2 to 2m (Fatka, painter)

Arc for the spider improved 2x2 (Polymeric covering) Choosing arcs for a spider is a task tha..

437.00 грн.

heading